RT8074 ? ds8074-07 november 2012 www.richtek.com 1 ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. applications z lcd tv and monitor z notebook computers z distributed power systems z ip phones z digital cameras general description the RT8074 is a high efficiency synchronous, step-down dc/dc converter. its input voltage range is from 2.7v to 5.5v and provides an adjustable regulated output voltage from 0.8v to 5v while delivering up to 4a of output current. the internal synchronous low on-resistance power switches increase efficiency and eliminate the need for an external schottky diode. the default switching frequency is set at 2mhz, if the rt pin is left open. it can also be varied from 200khz to 2mhz by adding an external resistor. current mode operation with external compensation allows the transient response to be optimized over a wide range of loads and output capacitors. ordering information 4a, 2mhz, synchronous step-down converter note : richtek products are : ` rohs compliant and compatible with the current require- ments of ipc/jedec j-std-020. ` suitable for use in snpb or pb-free soldering processes. features z z z z z high efficiency : up to 95% z adjustable frequency : 200khz to 2mhz z z z z z no schottky diode required z z z z z 0.8v reference allows low output voltage z z z z z low dropout operation : 100% duty cycle z z z z z enable function z z z z z internal soft-start z z z z z rohs compliant and halogen free pin configurations (top view) sop-8 (exposed pad) comp gnd en vin fb rt lx lx gnd 2 3 4 5 6 7 8 9 typical application circuit note : using all ceramic capacitors 3 en vin 4 RT8074 v in 2.7v to 5.5v rt 7 lx 5, 6 comp fb 8 1 gnd 2, 9 (exposed pad) r osc l 1.5h c out 22f r comp 10k v out c in 10f c comp 560pf 750 2k r1 r2 1.1v package type sp : sop-8 (exposed pad-option 2) RT8074 lead plating system g : green (halogen free and pb free)
RT8074 2 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. functional pin description function block diagram pin no. pin name pin function 1 comp error amplifier compensation point. the current comparator threshold increases with this control voltage. connect external compensation elements to this pin to stabilize the control loop. 2, 9 (exposed pad) gnd ground. the exposed pad must be soldered to a large pcb and connected to gnd for maximum power dissipation. 3 en enable control input. float or connect this pin to logic high for enable. connect to gnd for disable. 4 vin power input supply. decouple this pin to gnd with a capacitor. 5, 6 lx internal power mosfet switches output. connect this pin to the inductor. 7 rt oscillator resistor input. connecting a resistor from this pin to gnd sets the switching frequency. if this pin is floating, the frequency will be set at 2mhz internally. 8 fb feedback. receives the feedback voltage from a resistive divider connected across the output. marking information RT8074gsp : product number ymdnn : date code RT8074 gspymdnn driver nisen control logic n-mos i lim 0.7v 0.4v isen slope com osc output clamp ea 0.8v int-ss enable otp comp rt fb vin gnd sd lx uv p-g hiccup oc limit en
RT8074 3 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. absolute maximum ratings (note 1) z supply input v oltage, vin --------------------------------------------------------------------------------------- ? 0.3v to 6.5v z lx pin switch voltage -------------------------------------------------------------------------------------------- ? 0.3v to (v in + 0.3v) <10ns ---------------------------------------------------------------------------------------------------------------- ? 5v to 8.5v z other i/o pin v oltages ------------------------------------------------------------------------------------------- ? 0.3v to (v in + 0.3v) z lx pin switch current -------------------------------------------------------------------------------------------- 5a z power dissipation, p d @ t a = 25 c sop-8 (exposed pad) ------------------------------------------------------------------------------------------- 1.33w z package thermal resistance (note 2) sop-8 (exposed pad), ja -------------------------------------------------------------------------------------- 75 c/w sop-8 (exposed pad), jc ------------------------------------------------------------------------------------- 15 c/w z junction temperature --------------------------------------------------------------------------------------------- 150 c z lead temperature (soldering, 10 sec.) ---------------- ------------------------------------------------------- 260 c z storage temperature range ------------------------------------------------------------------------------------ ? 65 c to 150 c z esd susceptibility (note 3) hbm (human body model) -------------------------------------------------------------------------------------- 2kv electrical characteristics (v in = 3.3v, t a = 25 c, unless otherwise specified) recommended operating conditions (note 4) z supply input voltage, vin --------------------------------------------------------------------------------------- 2.7v to 5.5v z junction temperature range ------------------------------------------------------------------------------------ ? 40 c to 125 c z ambient temperature range ------------------------------------------------------------------------------------ ? 40 c to 85 c parameter symbol test conditions min typ max unit feedback reference voltage v ref 0.784 0.8 0.816 v active , v fb = 0.78v, not switching -- 460 -- dc bias current shutdown -- -- 10 a output voltage line regulation v in = 2.7v to 5.5v -- 0.1 -- %/v output voltage load regulation 0a < i load < 4a -- 0.25 -- % error amplifier trans-conductance gm -- 400 -- a/v current sense trans-resistance r t -- 0.3 -- r osc = 330k 0.8 1 1.2 switching frequency f sw switching 0.2 -- 2 mhz logic-high v ih 1.6 -- -- en input voltage logic-low v il -- -- 0.4 v switch on resistance, high r ds(on)_p i lx = 0.5a -- 110 180 m switch on resistance, low r ds(on)_n i lx = 0.5a -- 70 120 m
RT8074 4 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. note 1. stresses beyond those listed ? absolute maximum ratings ? may cause permanent damage to the device. these are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. exposure to absolute maximum rating conditions may affect device reliability. note 2. ja is measured at t a = 25 c on a high effective thermal conductivity four-layer test board per jedec 51-7. jc is measured at the exposed pad of the package. note 3. devices are esd sensitive. handling precaution is recommended. note 4. the device is not guaranteed to function outside its operating conditions. note 5. the RT8074 package surface temperature is about 60 c when the current is 3.15a. it is based on the 4-layer pcb referred in the layout considerations section. parameter symbol test conditions min typ max unit peak current limit i lim (note 5) 4.7 5.8 -- a v in rising -- 2.4 -- under voltage lockout threshold v in falling -- 2.2 -- v rt shutdown threshold v rt -- v in ? 0.7 v in ? 0.4 v
RT8074 5 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. typical operating characteristics reference voltage vs. temperature 0.76 0.77 0.78 0.79 0.80 0.81 0.82 0.83 0.84 -50 -25 0 25 50 75 100 125 temperature (c) reference voltage (v) v in = 5v, v out = 1.1v switching frequency vs. temperature 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 -50-250 255075100125 temperature (c) switching frequency (mhz) 1 v in = 5v, v out = 1.1v, i out = 0.6a efficiency vs. output current 0 10 20 30 40 50 60 70 80 90 100 00.511.522.533.54 output current (a) efficiency (%) v in = 5v, v out = 1.1v, i out = 0 to 4a output voltage vs. output current 1.094 1.096 1.098 1.100 1.102 1.104 1.106 1.108 1.110 1.112 00.511.522.533.54 output current (a) output voltage (v) v in = 5v, v out = 1.1v, i out = 0 to 4a v in uvlo vs. temperature 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 -50 -25 0 25 50 75 100 125 temperature (c) v in uvlo (v) rising v out = 1.1v falling enable voltage vs. temperature 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 -50 -25 0 25 50 75 100 125 temperature (c) enable voltage (v) rising v out = 1.1v falling
RT8074 6 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. output ripple time (500ns/div) v out (20mv/div) v lx (2v/div) v in = 5v, i out = 4a power off from en time (100 s/div) v in = 5v, v out = 1.1v, i out = 4a i out (5a/div) v lx (5v/div) v en (5v/div) v out (1v/div) time (500 s/div) power on from en i out (5a/div) v lx (5v/div) v in = 5v, v out = 1.1v, i out = 4a v en (5v/div) v out (1v/div) load transient response time (100 s/div) i out (2a/div) v out (200mv/div) v in = 5v, v out = 1.1v, i out = 1 to 4a, r comp = 10k , c comp = 560pf
RT8074 7 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. application information the basic ic application circuit is shown in typical application circuit. external component selection is determined by the maximum load current and begins with the selection of the inductor value and operating frequency followed by c in and c out . main control loop during normal operation, the internal high side power switch (p-mosfet) is turned on at the beginning of each clock cycle. the inductor current increases until it reaches the value defined by the output voltage (v comp ) of the error amplifier. the error amplifier adjusts its output voltage by comparing the feedback signal from a resistive voltage divider on the fb pin with an internal 0.8v reference. when the load current increases, it causes a reduction in the feedback voltage relative to the reference. the error amplifier increases its output voltage until the average inductor current matches the new load current. when the high side power mosfet shuts off, the synchronous power switch (n-mosfet) turns on until the beginning of the next clock cycle. output voltage setting the output voltage is set by an external resistive voltage divider according to the following equation : out ref r1 v = v x (1 ) r2 + where v ref is 0.8v typical. the resistive voltage divider allows the fb pin to sense a fraction of the output voltage as shown in figure 1. RT8074 fb gnd v out r1 r2 figure 1. setting the output voltage soft-start the RT8074 includes an internal soft-start function that gradually raises the clamp on the comp pin. operating frequency selection of the operating frequency is a tradeoff between efficiency and component size. high frequency operation allows the use of smaller inductor and capacitor values, but at the expense of efficiency. on the other hand, operation at lower frequency improves efficiency by reducing internal gate charge and switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. the operating frequency of the ic is determined by an external resistor, r osc , that is connected between the rt pin and ground. the value of the resistor sets the ramp current that is used to charge and discharge an internal timing capacitor within the oscillator. the practical switching frequency ranges from 200khz to 2mhz. however, when the rt pin is floating, the internal frequency is set at 2mhz. determine the rt resistor value by examining the curve below. please notice the minimum on time is about 90ns. figure 2. switching frequency vs. r rt resistor inductor selection for a given input and output voltage, the inductor value and operating frequency determine the ripple current. the ripple current, i l , increases with higher v in and decreases with higher inductance : out out l in vv i1 f x l v ?? ?? = ? ?? ?? ?? ?? 0.0 0.4 0.8 1.2 1.6 2.0 2.4 0 300 600 900 1200 1500 1800 2100 r rt (k ) switching frequency (mhz) 1
RT8074 8 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. having a lower ripple current reduces not only the esr losses in the output capacitors but also the output voltage ripple. highest efficiency operation is achieved by reducing ripple current at low frequency, but it requires a large inductor to attain this goal. for the ripple current selection, the value of i l = 0.4 (i max ) will be a reasonable starting point. the largest ripple current occurs at the highest v in . to guarantee that the ripple current stays below a specified maximum, the inductor value should be chosen according to the following equation : out out l(max) in(max) vv l1 f x i v ???? =? ???? ???? ???? using ceramic input and output capacitors higher value, lower cost ceramic capacitors are now becoming available in smaller case sizes. their high ripple current, high voltage rating and low esr make them ideal for switching regulator applications. however, care must be taken when these capacitors are used at the input and output. when a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input v in . at best, this ringing can couple to the output and be mistaken as loop instability. at worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at v in large enough to damage the part. slope compensation and inductor peak current slope compensation provides stability in constant frequency architectures by preventing sub harmonic oscillations at duty cycles greater than 50%. it is accomplished internally by adding a compensating ramp to the inductor current signal. normally, the maximum inductor peak current is reduced when slope compensation is added. for the RT8074, however, a separate inductor current signal is used to monitor over current condition, so this keeps the maximum output current relatively constant regardless of duty cycle. hiccup mode under voltage protection a hiccup mode under voltage protection (uvp) function is provided for the ic. when the fb voltage drops below half of the feedback reference voltage, v ref , the uvp function will be triggered to auto soft-start the power stage continuously until this event is cleared. the hiccup mode uvp reduces input current in short circuit conditions and prevents false triggering during soft-start process. under voltage lockout threshold the ic features input under voltage lockout protection (uvlo). if the input voltage exceeds the uvlo rising threshold voltage, the converter will reset and prepare the pwm for operation. if the input voltage falls below the uvlo falling threshold voltage during normal operation, the device will stop switching. the uvlo rising and falling threshold voltage has a hysteresis to prevent noise-caused reset. thermal considerations for continuous operation, do not exceed absolute maximum junction temperature. the maximum power dissipation depends on the thermal resistance of the ic package, pcb layout, rate of surrounding airflow, and difference between junction and ambient temperature. the maximum power dissipation can be calculated by the following formula : p d(max) = (t j(max) ? t a ) / ja where t j(max) is the maximum junction temperature, t a is the ambient temperature, and ja is the junction to ambient thermal resistance. for recommended operating condition specifications, the maximum junction temperature is 125 c. the junction to ambient thermal resistance, ja , is layout dependent. for sop-8 (exposed pad) packages, the thermal resistance, ja , is 75 c/w on a standard jedec 51-7 four-layer thermal test board. the maximum power dissipation at t a = 25 c can be calculated by the following formula : p d(max) = (125 c ? 25 c) / (75 c/w) = 1.333w for sop-8 (exposed pad) package the maximum power dissipation depends on the operating ambient temperature for fixed t j(max) and thermal resistance, ja . the derating curve in figure 3 allows the designer to see the effect of rising ambient temperature on the maximum power dissipation.
RT8074 9 ds8074-07 november 2012 www.richtek.com ? copyright 2012 richtek technology corporation. all rights reserved. is a registered trademark of ric htek technology corporation. layout considerations follow the pcb layout guidelines for optimal performance of the ic. ` connect the terminal of the input capacitor(s), c in , as close as possible to the vin pin. this capacitor provides the ac current into the internal power mosfets. ` lx node experiences high frequency voltage swing and should be kept within a small area. ` keep all sensitive small signal nodes away from the lx node to prevent stray capacitive noise pick up. ` connect the fb pin directly to the feedback resistors. the resistive voltage divider must be connected between v out and gnd. figure 3. derating curve of maximum power dissipation figure 4. pcb layout guide 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0 25 50 75 100 125 ambient temperature (c) maximum power dissipation (w) 1 four-layer pcb gnd comp gnd en vin fb rt lx lx gnd 2 3 4 5 6 7 8 9 place the compensation components as close to the ic as possible v out gnd r2 r1 v in c in c out v out l1 r comp c comp lx should be connected to inductor by wide and short trace. sensitive components should be kept away from this trace place the feedback resistors as close to the ic as possible place the input and output capacitors as close to the ic as possible r osc
RT8074 10 ds8074-07 november 2012 www.richtek.com richtek technology corporation 5f, no. 20, taiyuen street, chupei city hsinchu, taiwan, r.o.c. tel: (8863)5526789 richtek products are sold by description only. richtek reserves the right to change the circuitry and/or specifications without notice at any time. customers should obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. richtek cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a richtek product. information furnish ed by richtek is believed to be accurate and reliable. however, no responsibility is assumed by richtek or its subsidiaries for its use; nor for any infringeme nts of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of r ichtek or its subsidiaries. outline dimension a b j f h m c d i y x exposed thermal pad (bottom of package) 8-lead sop (exposed pad) plastic package dimensions in millimeters dimensions in inches symbol min max min max a 4.801 5.004 0.189 0.197 b 3.810 4.000 0.150 0.157 c 1.346 1.753 0.053 0.069 d 0.330 0.510 0.013 0.020 f 1.194 1.346 0.047 0.053 h 0.170 0.254 0.007 0.010 i 0.000 0.152 0.000 0.006 j 5.791 6.200 0.228 0.244 m 0.406 1.270 0.016 0.050 x 2.000 2.300 0.079 0.091 option 1 y 2.000 2.300 0.079 0.091 x 2.100 2.500 0.083 0.098 option 2 y 3.000 3.500 0.118 0.138
|
